Overview

   This article will detail setting up the zebra browser print service.  

Procedure

1. Connecting your Zebra ZD410 printer
2. Insert your Zebra ZD410 label roll
3. Calibrate your Zebra ZD410 printer
4. Install the Zebra Browser Print application (Windows or Mac)
5. Printing your first label.

Insert your Zebra ZD410 label roll

1. To open the printer's lid, pull the yellow latches towards you and lift the lid upwards.
2. Pull the yellow roll guides apart and insert the roll with the labels face up.
3. Release the roll guides and push them together to make sure the roll is secure and turning freely.
4. Pull the labels out past the cutter at the front of the printer.
5. Push the labels under the roll guides.
6. Flip the labels up and align the media sensor to the center position.
7. Push the lid down to snap both yellow latches shut.

1. For the printer to recognize the size of your labels, perform an initial calibration:
2. Follow the steps in sections 1 to 2 above.
3. Press the power button and wait for the solid green status indicator light.
4. Hold the pause and cancel buttons down for 2 seconds and let go. The printer will measure and feed a few blank labels.
5. Once the printer stops and the status indicator light is solid green, the calibration is complete.
   
   NOTE: An initial calibration is necessary when the new roll is a different label size.
   You do not need to calibrate after inserting a new roll of the same label size. The printer will automatically adjust or you can press the feed button twice before printing.
   If you are using the discontinued Zebra LP2824 Plus, hold down the green feed button and release after the status light ring flashes once and then twice.
   
   

Install the Zebra Browser Print application (Windows or Mac)

1. Download the Zebra Browser Print application.
   • Download for Windows PC (Windows 7, Windows 10)
   • Download for Mac (OSX)
2. From the bottom left of your Browser window, click the ZebraBrowserPrintSetup-1.2.1.279.exe (The file extension will be .dmg for Mac)
3. From the User Account Control window, click Yes. This window may not appear for everyone.
4. From the Setup - Zebra Browser Print window, click Next > Next > Next > Install > Finish.
5. Read the Browser Print End User License Agreement and click I Agree.
6. From the Browser Print Security Certificate window, click OK. This will launch your computer's default browser.
   If your browser does not open, navigate to https://localhost:9101/ssl_support
7. From the browser window, click Advanced > Proceed to localhost (unsafe) > Yes.
   Once you see the message "SSL Certificate Has been accepted. Retry connection."
8. Navigate to chrome://flags/#allow-insecure-localhost and select "Enable" the flag for "Allow invalid certificates for resources loaded from localhost" > Relaunch Now.
9. You can close the browser tab.
10. Right click on Zebra Browser print and click on settings.
11. Enable Broadcast search and Driver search.
12. Click on Change button at the top and select the right printer.
    
    

Printing your first label


Printing your first label 

If after following the above steps to install Zebra Browser Print either did not work or has stopped working, Here are some steps that may resolve the issue. 

Zebra Browser Prints requires HTTPS:// please make sure the https:// is included on the cloudretailer website and remove port number if it's included. 

If the printer is still not calibrated after Step 3, you will need to perform the calibration from Zebra Setup Utilities.

1. If Zebra Setup Utilities is already installed, go to Step 9.
2. Download Zebra Setup Utilities.
3. From the bottom left of your Browser window, click the zsu-1191269.exe.
4. From the User Account Control window, click Yes. This window may not appear for everyone.
5. From the Zebra Setup Utilities - InstallAware Wizard window, click Next.
6. Read the End User License Agreement and click "I accept the terms of the license agreement", then click Next > Next > Next > Next.
7. Read the Important Information and click "I have read the information above", then click Next.
8. Click Finish.
9. Run Zebra Setup Utilities from the Start menu.
10. From the User Account Control window, click Yes. This window may not appear for everyone.
11. From the Preloading Drivers screen, click Next > choose your printer port (probably USB) > click Next > click Finish.
    This window only appears the first time you run Zebra Setup Utilities.

12. Select the printer from the Printers list, then click the Open Printer Tools button in the Printer Configuration section.

13. Click the Configure Printer Settings Button > Verify the settings match the label's dimenstions.  Then Click Finish.

14. From the Tools windows, click the Action tab.
15. Click the Calibrate media action to highlight it, then click the Send button.
16. The printer will measure and feed a few blank labels.
17. Once the printer stops and the status indicator light is solid green, the calibration is complete.

18. If necessary, you can also Load factory defaults and Reset printer from the Action tab.

References